Trades and Apprenticeship

The instant the ignition switch is turned to the start position, ________.

The instant the ignition switch is turned to the start position, ________.

The instant the ignition switch is turned to the start position, ________.
A) The hold in winding is energized
B) The pull in winding is energized
C) The starter motor starts to rotate before energizing the starter pinion gear
D)

12

motorhead   2068   27 Replies

Lil Sonic

Technician A says that dragging brakes are often discovered when mounting the alignment sensors on t

Technician A says that dragging brakes are often discovered when mounting the alignment sensors on t

Technician A says that dragging brakes are often discovered when mounting the alignment sensors on the wheels. Technician B says that dragging brakes on one side of the vehicle will cause a pull. Which technician is correct?
A) Technician A only

123

motorhead   1315   28 Replies

evol.cliff

Which type of variable effort steering design uses a variable bi-directional magnetic rotary actuato

Which type of variable effort steering design uses a variable bi-directional magnetic rotary actuato

Which type of variable effort steering design uses a variable bi-directional magnetic rotary actuator built into the steering rack?
A) Magnasteer      B) TFE      C) EVO      D) SSS

123

motorhead   2748   28 Replies

Bruce Gordon1

Technician A says that generic scan tools must be able to read all generic OBD-II codes. Technician

Technician A says that generic scan tools must be able to read all generic OBD-II codes. Technician

Technician A says that generic scan tools must be able to read all generic OBD-II codes. Technician B says that all generic scan tools must be able to read manufacturer OBD-II trouble codes. Which technician is correct?
A) Technician A  &nb

123

motorhead   1283   29 Replies

Ethan White1

Technician A says that a 3 x 5 card should be held against the oil fill opening if the PCV system is

Technician A says that a 3 x 5 card should be held against the oil fill opening if the PCV system is

Technician A says that a 3 x 5 card should be held against the oil fill opening if the PCV system is operating correctly. Technician B says that if a PCV valve rattles, it definitely is good. Which technician is correct?
A) Technician A  &n

123

motorhead   3292   30 Replies

King Slime1

Technician A says that CO and HC levels should increase if the AIR hoses are pinched off. Technician

Technician A says that CO and HC levels should increase if the AIR hoses are pinched off. Technician

Technician A says that CO and HC levels should increase if the AIR hoses are pinched off. Technician B says that a defective drive belt may cause AIR system problems. Which technician is correct?
A) Technician A      B) Technician

123

motorhead   1154   30 Replies

Drew Bonjour

Technician A says that valve springs should be kept with the valve at the time of disassembly and te

Technician A says that valve springs should be kept with the valve at the time of disassembly and te

Technician A says that valve springs should be kept with the valve at the time of disassembly and tested for squareness and proper spring force. Technician B says that the exhaust valve is about 50 percent of the size of the intake valve. Who is righ

123

motorhead   1882   30 Replies

Riyadh Aboughali

Technician A says most engine flywheels are lightweight to avoid causing inertia. Technician B says

Technician A says most engine flywheels are lightweight to avoid causing inertia. Technician B says

Technician A says most engine flywheels are lightweight to avoid causing inertia. Technician B says most engine flywheels are made of hardened forged steel to absorb the heat of clutch operation. Which technician is correct?
A) Technician A only

123

motorhead   5476   34 Replies

mag90si

Brake fluid boiling point can be measured using ________.

Brake fluid boiling point can be measured using ________.

Brake fluid boiling point can be measured using ________.
A) A candy thermometer      B) A hygrometer
C) A Styrofoam cup      D) An electronic tester

123

motorhead   2268   34 Replies

Evan H

The crankshaft journals have been turned. What size bearings should be installed?

The crankshaft journals have been turned. What size bearings should be installed?

The crankshaft journals have been turned. What size bearings should be installed?
A) Oversize      B) Undersize
C) Standard      D) It makes no difference which size is installed

123

motorhead   2503   36 Replies

moodymoods

Technician A says that when the MIL is on, the technician should retrieve the DTC and follow the man

Technician A says that when the MIL is on, the technician should retrieve the DTC and follow the man

Technician A says that when the MIL is on, the technician should retrieve the DTC and follow the manufacturer's recommended procedure to find the root cause of the problem. Technician B says that all OBD II monitors must have the enable criteria

1234

motorhead   1750   45 Replies

Drew Bonjour

Technician A says most transmission hydraulic valves are spool valves. Technician B says the recesse

Technician A says most transmission hydraulic valves are spool valves. Technician B says the recesse

Technician A says most transmission hydraulic valves are spool valves. Technician B says the recessed areas of a spool valve are called grooves. Which technician is correct?
A) Technician A      B) Technician B     

1234

motorhead   4092   46 Replies

J M1

An easy check of the adaptive front light system (AFS) is to ________.

An easy check of the adaptive front light system (AFS) is to ________.

An easy check of the adaptive front light system (AFS) is to ________.
A) Cycle the brake switch
B) Check that the system performs a self-test during start-up
C) Open and close the driver's door
D) None of these

1234

motorhead   3812   47 Replies

Nathan Faga

The typical RWD drive shaft rotates how many times faster than the wheels?

The typical RWD drive shaft rotates how many times faster than the wheels?

The typical RWD drive shaft rotates how many times faster than the wheels?
A) Three      B) One
C) Two      D) It rotates at the same speed

1234

motorhead   3889   51 Replies

Jetbourg M. Bañares